Set of column slewing crane 1ton electric chain hoist 1ton with hook
Set of manual column slewing crane KZK100 with electric chain hoist KT1006 and manual trolley HNRK1T. Lifting capacity 1000kg.
Features of the slewing crane 1 tonne (KZK100)
Industrial column slewing crane manual, 1 ton with jib length 3 meters.
This Industrial 270° slewing crane with manual operation is suitable for various applications such as lifting at loading and unloading areas, manipulating workpieces, lifting on floor floors, workstations with tool changes, outside at the unloading quay, etc.
Advantages:
Manual slewing crane
Suitable for use with optional hoists and lifting accessories, both manual and electric
Load capacity 1 ton, over the entire jib length
Overall boom length of 3000mm, and a total reach of 6000mm
Swing angle of 270
Limited height, and therefore also suitable for low spaces
Characteristics:
Dimensions of horizontal H-beam: beam width 100mm, beam height 200mm
Vertical column with bottom plate with thickness of 16mm
Diameter of bottom plate: 700mm
Total column height of 3000 meters, net height of 2500mm
The mounting of the bottom plate should be done with chemical anchoring on a sufficiently strong concrete slab. A reinforced concrete base is recommended of 1.5x1.5x1.5 meters with strength C20/25 (B25), with cast-in threaded rods.
Finished in primer RAL7035
Tips for assembly:
Supplied without fasteners.
The mounting of the base should be done with appropriate chemical anchoring on a sufficiently strong concrete slab. A reinforced concrete base is recommended of 1.5x1.5x1.5 meters with strength C20/25 (B25), with a cast-in-place steel structure with fixing bolts
The crane is delivered in 2 parts, and is installed by the customer. It is recommended to provide a forklift, lifting aids, and 2 persons for a full working day for the installation
Optionally, the installation can be performed by our services. Contact our inside sales department for more information
Supplied with 2 spray cans of primer for touching up any minor scratches after assembly
Features of the 1 tonne electric chain hoist (KT1006)
Industrial electric chain hoist 1 ton 6 meters with hook
Hoist with safety hook for direct suspension without trolley, on a tube, in a rack, hoisting opening or elevator shaft.
Also suitable for use in combination with a trolley 1 ton, for moving on an H-beam.
Features:
Capacity 1 ton
Lifting height 6 meters
Voltage 3x400V
Chain hoist type: with suspension hook
Wired remote control (length 6m) with emergency stop and steel suspension cable
Control circuit on low voltage 24V
Limit switch stops the chain in both directions in good time
Powerful motor with M4 30% duty cycle, for industrial use in production areas
Protected against overload with a slip clutch
Gearbox made of high-strength alloy with low noise production
G80 chain designed for industrial use and approved for the toughest conditions
Chain is collected in a PVC bag on the hoist, so it never hangs in the way
IP54 dust and spray waterproof, suitable for dusty, dirty and wet working environments
Single lifting chain with link thickness 7.1mm
Swivel hook 360° freely rotatable with safety valve
Supplied with 0.6 meter power cable, without plug
Built-in phase change safety, prevents the hoist from operating if the phases are reversed
Optional accessories:
Lifting clamp 1 ton (716172001) for lifting steel plates and beams
Lifting magnets from 100 to 1000kg (PLM101, PLM301, PLM601, PLM1001). Suitable for lifting steel plate materials and beams
Net trolley length mm 3000
Angle of rotation ° 270
Lifting height mm 2500
Wireless Do not possess the feature
Weight kg 570.00
Dimensions (l x b x h) mm 2.5x1.1x2.5
